Skip to content
MountainsideFoam & Coating, Sacramento24/7 roof line(916) 963-8097

Sealing manufactured home roofs

Mobile home roof coating in Sacramento, CA

Your mobile home roof leaks at the seams, the screws are backing out and the whole unit heats up all summer, and a full reroof costs thousands.

Typical range$1,150 to $3,480
Pricedper job
Phone lineOpen 24/7
Single-wide mobile home roof in a Sacramento-area park being coated white
Quick answer

Mobile home roof coating seals and protects a metal or rolled roofing manufactured home by repairing seams, fasteners and vents, then applying an acrylic or silicone coat. It stops common leaks and reduces heat. Typical Sacramento cost is 1,150 to 3,480 per job, and most homes take one to two days.

What this job involves

Manufactured home roofs are light, often low-slope and built from thin galvanized steel, aluminum or a rolled membrane. They expand and contract strongly with temperature, which loosens screws, splits seam sealant and opens gaps around vents and the edge trim. Sacramento's heat cycle makes this worse than in milder climates, so many parks have roofs that leak by their second decade. Most leaks start at fasteners, not in the panel.

A coating system is a sound fix for most of those roofs. It seals the roof as a single skin, adds reflectivity that lowers the temperature inside the home, and costs far less than replacement. It does not fix a sagging truss or rotted decking, so we inspect from the roof and sometimes from inside the home before we recommend it. We tell you which case applies. That keeps the price honest and the repair lasting.

Warning signs

Signs your mobile home roof needs coating

1Stains on ceiling panels

Brown rings on interior ceiling panels point to a leak, often at a seam or screw. The water can travel along the metal before it drips.

2Rust at screws and seams

Orange stains around fasteners and panel edges show the sealant has failed and the metal is beginning to corrode. Orange stains around fasteners and panel edges show the sealant has failed and the metal is starting to corrode.

3Loose or lifted edge trim

Edge trim that has pulled away from the roof leaves a gap where wind-driven rain gets into the roof and walls.

4Cracked vent flashings

Plumbing vents and roof vents have rubber or sealant collars that dry out in the sun, causing a common leak.

5Peeling old coating

A previous coating that is flaking or bubbling has lost adhesion. It must be removed in loose areas and the roof primed before recoating.

6Home runs hot all summer

Dark or bare metal roofs absorb strong sun. A reflective coating can bring down roof surface and attic temperature in July.

Inspecting a mobile home roof properly

We begin by walking the roof carefully, since thin manufactured home roofs can flex or dent under weight. We check every screw, seam, vent, vent collar, skylight, air conditioner curb and the full edge trim. We also look for soft spots, which can point to wet insulation or decking, and check the ceiling inside for damp areas. If the roof structure is sound, a coating job is a good fit. If decking is soft or large sections are rusted through, we explain that repair or partial re-sheathing needs to come first. Being clear about this at the start avoids the common case where a coat is applied over a failing roof and leaks again in a year.

A sealed roof seam on a mobile home with embedded fabric
A sealed roof seam on a mobile home with embedded fabric.

Seams, screws and vents come first

Before any coating goes on, we reset or replace loose screws, using larger fasteners where holes are stripped, and seal each head. Seams are cleaned and sealed with butyl or sealant, then covered with reinforcing fabric. Vent collars, antenna mounts and the air conditioner curb get fabric and mastic, which creates a flexible patch that handles movement. After these repairs, the roof is washed, any rust is treated and primed, and the coating goes on in two coats. Acrylic is common on mobile homes because it drains well off the typical slight crown, and silicone is chosen where the roof has low spots that hold water, such as the center of a flat roof.

  • Reset or replace loose screws
  • Seal and fabric-reinforce every seam
  • Re-seal vent and antenna collars
  • Treat rust and prime bare metal
  • Two coats, checked for thickness

Coating versus reroofing a mobile home

Coating is often the right fit when the metal is sound and the leaks come from seams and fasteners. It costs a fraction of a new roof and does not require removing the old surface, which means less disruption in a park where space is tight. A roof-over with new metal panels or a rubber membrane costs more but adds a structural layer. Reroofing becomes the better option when rust has eaten through panels, when the decking is wet and soft, or when the roof has been coated many times and the buildup is heavy. We will tell you which case you are in. If you rent your space, check your park's rules about roof work, since some parks require notice or have approved materials.

How the job runs

Our process for mobile home roof coating

Six steps, in the order the crew does them on a Sacramento roof.

  1. Step 1Walk and inspect roof

    We walk the roof with care, check screws, seams, vents and trim, and look for soft spots or interior ceiling stains.

  2. Step 2Wash and treat rust

    The roof is cleaned, loose coating is removed and rust is brushed and treated to stop it from spreading further.

  3. Step 3Fix screws and seams

    Loose screws are replaced, seams are sealed with butyl or sealant, and fabric reinforcement covers laps and joints. Loose screws are replaced, seams are sealed with butyl or sealant, and fabric reinforcement covers every lap and joint.

  4. Step 4Seal vents and trim

    Vent collars, the air conditioner curb and edge trim are re-sealed with fabric and mastic to stop edge and penetration leaks.

  5. Step 5Prime and coat roof

    Bare or rusted metal is primed, then two coats of acrylic or silicone are applied to the specified dry mil thickness.

  6. Step 6Final check and tips

    We inspect for pinholes, clear the edges and give you simple care tips, such as yearly checks and washing the roof.

Cost

What mobile home roof coating costs in Sacramento

MS-120 Mobile Home Roof Coating2026 range
$1,150 to $3,480per job

A typical 14 by 66 foot single-wide with seam sealing, screw replacement and two acrylic coats runs near 1,850 to 2,640.

What moves the price
  • Home size and roof type
  • Amount of rust and screw repair
  • Acrylic or silicone coating
  • Vents, skylights and add-ons

Planning a recoat? The coating calculator turns roof area, coating type and target thickness into gallons and pails.

Sacramento conditions that matter

Sacramento area has many mobile home parks, from older parks in Rancho Cordova and North Highlands to communities in Elk Grove and Citrus Heights. The roofs there face long hot summers, with metal expanding in the afternoon heat and contracting overnight, and winter rain that finds every loose screw. A reflective coating can lower the heat that reaches the interior, which helps for residents who pay SMUD bills and rely on window air conditioners. Park rules vary, so ask the manager about roof work approval and any restrictions on materials, and tell us about any park schedule or access limits.

FAQ

Questions about mobile home roof coating

Can I coat a mobile home roof if I rent the lot?

Usually yes, since you own the home, but parks often have rules on roof work, material colors or notice before contractors come in. Check your lease or ask the manager first. We can work around park hours and keep vehicles and neighbors clear while the crew is on site.

Why does my mobile home roof leak around the screws?

Thin metal expands and shrinks each day, which works the screws loose and cracks the rubber washers. Rain then follows the screw into the roof. The fix is replacing stripped screws with larger ones and sealing every head before coating, not just painting over them.

Is it safe to walk on my mobile home roof?

Not without care. Manufactured home roofs are light and can dent or flex, especially away from the rafters. Crews use walk boards and stay on supported lines. If you need to check something, call us rather than climb up yourself. Roof edges and vents are the weakest zones.

How long does coating a mobile home take?

Most single-wide homes take a day, and double-wides or those with heavy repairs take two. Weather plays a part, since the roof must be dry and the coat needs time to dry before dew or rain. We schedule for a dry stretch and tell you the timing in advance.

Do I need to remove my old roof coating first?

Only where it is loose or peeling. Solid coating that is well adhered can be washed and recoated, with a primer if needed. We test adhesion in a few spots, and cut out failing areas before applying new coating to avoid trapping bad material under the new film.

Roof leaking, peeling or baking in the sun?

Call the 24/7 line. Tell us the roof type, where the water shows up or what the coating looks like, and we will tell you what we would check first and when a crew can be there.

Call (916) 963-8097
Call 24/7 (916) 963-8097